求救！BX54E开机一直闪灯，进不了后台搜不到wifi

BX54E开机一直闪灯，lan口连电脑不识别，进不了后台搜不到wifi。按钮重置故障依旧。ttl接线启动日志如下，大神帮忙看看是哪出问题

Format: Log Type - Time(microsec) - Message - Optional Info

Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic

S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1.1-00044

S - IMAGE_VARIANT_STRING=MAACANAZA

S - OEM_IMAGE_VERSION_STRING=node-sh-06

S - Boot Config, 0x000002c5

B -       128 - PBL, Start

B -      1564 - bootable_media_detect_entry, Start

B -      3356 - bootable_media_detect_success, Start

B -      3360 - elf_loader_entry, Start

B -      8443 - auth_hash_seg_entry, Start

B -      8802 - auth_hash_seg_exit, Start

B -     99260 - elf_segs_hash_verify_entry, Start

B -    167264 - PBL, End

B -    137860 - SBL1, Start

B -    198311 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4

B -    206637 - clock_init, Start

D -      7289 - clock_init, Delta

B -    214079 - boot_flash_init, Start

D -     17964 - boot_flash_init, Delta

B -    232105 - boot_config_data_table_init, Start

D -      5002 - boot_config_data_table_init, Delta - (575 Bytes)

B -    240187 - Boot Setting :  0x00000618

B -    246379 - CDT version:2,Platform ID:8,Major ID:4,Minor ID:0,Subtype:1

B -    253302 - sbl1_ddr_set_params, Start

B -    254888 - Pre_DDR_clock_init, Start

B -    260561 - Pre_DDR_clock_init, End

B -    803949 - do ddr sanity test, Start

D -        30 - do ddr sanity test, Delta

B -    808616 - Image Load, Start

D -    234819 - QSEE Image Loaded, Delta - (523680 Bytes)

B -   1044259 - Image Load, Start

D -     14640 - DEVCFG Image Loaded, Delta - (13592 Bytes)

B -   1058929 - Image Load, Start

D -    186569 - APPSBL Image Loaded, Delta - (419920 Bytes)

B -   1245589 - QSEE Execution, Start

D -        30 - QSEE Execution, Delta

B -   1252055 - SBL1, End

D -   1116666 - SBL1, Delta

S - Flash Throughput, 2289 KB/s  (958439 Bytes,  418573 us)

S - DDR Frequency, 800 MHz

S - Core 0 Frequency, 800 MHz

 

 

U-Boot 2016.01 (May 18 2021 - 13:19:54 +0800)

 

DRAM:  smem ram ptable found: ver: 1 len: 4

512 MiB

NAND:  QPIC controller support serial NAND

ID = 7f7f11c8

Vendor = c8

Device = 11

Serial Nand Device Found With ID : 0xc8 0x11

Serial NAND device Manufature:F50D1G41LB(2M)

Device Size:128 MiB, Page size:2048, Spare Size:64, ECC:4-bit

SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000

ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)

128 MiB

MMC:   sdhci: Node Not found, skipping initialization

 

PCI Link Intialized

PCI1 is not defined in the device tree

In:    serial@78AF000

Out:   serial@78AF000

Err:   serial@78AF000

machid: 8040001

eth0 MAC Address from ART is not valid

eth1 MAC Address from ART is not valid

 

***************************************************************************

*                                                                         *

*                       H3C BX54E Boot, Version 102                       *

*                                                                         *

***************************************************************************

 

Hit any key to stop autoboot:  0

ubi0: attaching mtd1

ubi0: scanning is finished

ubi0: attached mtd1 (name "mtd=0", size 45 MiB)

ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096

ubi0: good PEBs: 362, bad PEBs: 0, corrupted PEBs: 0

ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128

ubi0: max/mean erase counter: 136/29, WL threshold: 4096, image sequence number: 1350110114

ubi0: available PEBs: 0, total reserved PEBs: 362, PEBs reserved for bad PEB handling: 20

Read 0 bytes from volume kernel to 44000000

No size specified -> Using max size (4077388)

## Loading kernel from FIT Image at 44000000 ...

   Using 'config@mp03.1' configuration

   Trying 'kernel@1' kernel subimage

     Description:  ARM OpenWrt Linux-4.4.60

     Type:         Kernel Image

     Compression:  lzma compressed

     Data Start:   0x440000e4

     Data Size:    2950128 Bytes = 2.8 MiB

     Architecture: ARM

     OS:           Linux

     Load Address: 0x41208000

     Entry Point:  0x41208000

     Hash algo:    crc32

     Hash value:   068640d0

     Hash algo:    sha1

     Hash value:   72b1dd1863e03440f5adcaf31b7528e73eb35ed4

   Verifying Hash Integrity ... crc32+ sha1+ OK

## Loading fdt from FIT Image at 44000000 ...

   Using 'config@mp03.1' configuration

   Trying 'fdt@mp03.1' fdt subimage

     Description:  ARM OpenWrt qcom-ipq50xx-mpxx device tree blob

     Type:         Flat Device Tree

     Compression:  uncompressed

     Data Start:   0x44340c14

     Data Size:    55772 Bytes = 54.5 KiB

     Architecture: ARM

     Hash algo:    crc32

     Hash value:   ff46b3d0

     Hash algo:    sha1

     Hash value:   551ec1f4104e54bd6dd2a4e740e110423e00196d

   Verifying Hash Integrity ... crc32+ sha1+ OK

   Booting using the fdt blob at 0x44340c14

   Uncompressing Kernel Image ... OK

   Loading Device Tree to 4a3ef000, end 4a3ff9db ... OK

Could not find PCI in device tree

Using machid 0x8040001 from environment

 

Starting kernel ...

 

[    0.000000] Booting Linux on physical CPU 0x0

[    0.000000] Initializing cgroup subsys cpuset

[    0.000000] Initializing cgroup subsys cpu

[    0.000000] Initializing cgroup subsys cpuacct

[    0.000000] Linux version 4.4.60 (j11967@ubuntu202-UIS-R190-G2) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 4c6772572d16+r49254) ) #1 SMP PREEMPT Tue May 18 15:09:41 CST 2021

[    0.000000] CPU: ARMv7 Processor [51af8014] revision 4 (ARMv7), cr=10c0383d

[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[    0.000000] Machine model: Qualcomm Technologies, Inc. IPQ5018/AP-MP03.1

[    0.000000] Ignoring memory range 0x40000000 - 0x41000000

[    0.000000] Reserved memory: created DMA memory pool at 0x4ea00000, size 16 MiB

[    0.000000] Reserved memory: initialized node dma_pool1@4ea00000, compatible id shared-dma-pool

[    0.000000] Memory policy: Data cache writealloc

[    0.000000] psci: probing for conduit method from DT.

[    0.000000] psci: PSCIv1.0 detected in firmware.

[    0.000000] psci: Using standard PSCI v0.2 function IDs

[    0.000000] psci: MIGRATE_INFO_TYPE not supported.

[    0.000000] PERCPU: Embedded 11 pages/cpu @9eb62000 s14912 r8192 d21952 u45056

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 104868

[    0.000000] Kernel command line: cOnsole=ttyMSM0,115200n8 cnss2.bdf_integrated=0x24 cnss2.bdf_pci0=0xA0 cnss2.bdf_pci1=0xA0 cnss2.skip_radio_bmap=4 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1 coherent_pool=2M

[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[    0.000000] Memory: 408500K/423936K available (6305K kernel code, 353K rwdata, 1912K rodata, 1024K init, 360K bss, 15436K reserved, 0K cma-reserved, 0K highmem)

[    0.000000] Virtual kernel memory layout:

[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)

[    0.000000]     vmalloc : 0x9f800000 - 0xff800000   (1536 MB)

[    0.000000]     lowmem  : 0x80000000 - 0x9f000000   ( 496 MB)

[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)

[    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)

[    0.000000]       .text : 0x80208000 - 0x80b06740   (9210 kB)

[    0.000000]       .init : 0x80c00000 - 0x80d00000   (1024 kB)

[    0.000000]       .data : 0x80d00000 - 0x80d58418   ( 354 kB)

[    0.000000]        .bss : 0x80d5b000 - 0x80db5314   ( 361 kB)

[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1

[    0.000000] Preemptible hierarchical RCU implementation.

[    0.000000]  Build-time adjustment of leaf fanout to 32.

[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.

[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2

[    0.000000] NR_IRQS:16 nr_irqs:16 16

[    0.000000] Architected cp15 timer(s) running at 24.00MHz (virt).

[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns

[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns

[    0.000020] Switching to timer-based delay loop, resolution 41ns

[    0.000520] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)

[    0.000537] pid_max: default: 32768 minimum: 301

[    0.000653] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.000663] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.001334] Initializing cgroup subsys io

[    0.001359] Initializing cgroup subsys memory

[    0.001393] Initializing cgroup subsys devices

[    0.001407] Initializing cgroup subsys freezer

[    0.001418] Initializing cgroup subsys net_cls

[    0.001429] Initializing cgroup subsys pids

[    0.001475] CPU: Testing write buffer coherency: ok

[    0.001931] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

[    0.002002] Setting up static identity map for 0x41300000 - 0x41300058

[    0.052796] MSM Memory Dump base table set up

[    0.052827] MSM Memory Dump apps data table set up

[    0.090510] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001

[    0.090647] Brought up 2 CPUs

[    0.090668] SMP: Total of 2 processors activated (96.00 BogoMIPS).

[    0.090674] CPU: All CPU(s) started in SVC mode.

[    0.104319] VFP support v0.3: implementor 51 architecture 3 part 40 variant 3 rev 4

[    0.104715] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns

[    0.104750] futex hash table entries: 512 (order: 3, 32768 bytes)

[    0.105290] pinctrl core: initialized pinctrl subsystem

[    0.106660] NET: Registered protocol family 16

[    0.108069] DMA: preallocated 2048 KiB pool for atomic coherent allocations

[    0.130299] cpuidle: using governor ladder

[    0.160330] cpuidle: using governor menu

[    0.160653] NET: Registered protocol family 42

[    0.165736] qcom,gcc-ipq5018 1800000.gcc: Registered ipq5018 GCC clocks provider

[    0.171598] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !

[    0.183185] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.

[    0.183201] hw-breakpoint: maximum watchpoint size is 8 bytes.

[    0.185016] CPU: IPQ5018, SoC Version: 1.1

[    0.186920] IPC logging disabled

[    0.186931] IPC logging disabled

[    0.186936] IPC logging disabled

[    0.186941] IPC logging disabled

[    0.186945] IPC logging disabled

[    0.187430] drv_flash_read filp_open 0:APPSBLENV error!

[    0.187783] sps:sps is ready.

[    0.188047] Registered Ethport

[    0.222793] pps_core: LinuxPPS API ver. 1 registered

[    0.222807] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>

[    0.222837] PTP clock support registered

[    0.224873] Advanced Linux Sound Architecture Driver Initialized.

[    0.225873] clocksource: Switched to clocksource arch_sys_counter

[    0.228473] NET: Registered protocol family 2

[    0.229384] TCP established hash table entries: 4096 (order: 2, 16384 bytes)

[    0.229440] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

[    0.229515] TCP: Hash tables configured (established 4096 bind 4096)

[    0.229580] UDP hash table entries: 256 (order: 1, 8192 bytes)

[    0.229605] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[    0.229839] NET: Registered protocol family 1

[    0.231163] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available

[    0.240361] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.240386] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.245952] Key type asymmetric registered

[    0.245976] Asymmetric key parser 'x509' registered

[    0.246032] io scheduler noop registered

[    0.246049] io scheduler deadline registered (default)

[    0.248954] a0000000.pci supply vdda not found, using dummy regulator

[    0.249031] a0000000.pci supply vdda_phy not found, using dummy regulator

[    0.249094] a0000000.pci supply vdda_refclk not found, using dummy regulator

[    0.249856] PCI host bridge /soc/pci@a0000000 ranges:

[    0.249887]    IO 0xa0200000..0xa02fffff -> 0xa0200000

[    0.249902]   MEM 0xa0300000..0xb02fffff -> 0xa0300000

[    0.585873] qcom-pcie a0000000.pci: link up

[    0.586101] qcom-pcie a0000000.pci: PCI host bridge to bus 0001:00

[    0.586119] pci_bus 0001:00: root bus resource [bus 00-ff]

[    0.586133] pci_bus 0001:00: root bus resource [io  0x0000-0xfffff] (bus address [0xa0200000-0xa02fffff])

[    0.586145] pci_bus 0001:00: root bus resource [mem 0xa0300000-0xb02fffff]

[    0.586571] PCI: bus0: Fast back to back transfers disabled

[    0.586590] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring

[    0.587608] PCI: bus1: Fast back to back transfers disabled

[    0.587689] pci 0001:00:00.0: BAR 8: assigned [mem 0xa0400000-0xa05fffff]

[    0.587706] pci 0001:00:00.0: BAR 9: assigned [mem 0xa0600000-0xa07fffff 64bit pref]

[    0.587721] pci 0001:00:00.0: BAR 0: assigned [mem 0xa0300000-0xa0300fff 64bit]

[    0.587740] pci 0001:00:00.0: BAR 7: assigned [io  0x1000-0x1fff]

[    0.587757] pci 0001:01:00.0: BAR 0: assigned [mem 0xa0400000-0xa05fffff 64bit]

[    0.587806] pci 0001:00:00.0: PCI bridge to [bus 01]

[    0.587818] pci 0001:00:00.0:   bridge window [io  0x1000-0x1fff]

[    0.587830] pci 0001:00:00.0:   bridge window [mem 0xa0400000-0xa05fffff]

[    0.587842] pci 0001:00:00.0:   bridge window [mem 0xa0600000-0xa07fffff 64bit pref]

[    0.587912] PCIe: RC0 enabled during bootup

[    0.594866] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set

[    0.595379] bt_driver 1943008.bt: bt_parse_ipc

[    0.595446] bt_driver 1943008.bt: bt_parse_mem

[    0.595492] bt_driver 1943008.bt: bt_parse_dt operating in secure mode

[    0.596795] 58000.qcom,msm-eud: ttyEUD0 at MMIO 0x0 (irq = 123, base_baud = 0) is a EUD UART

[    0.597408] Registered Sucessfully

[    0.598042] msm_serial 78af000.serial: msm_serial: detected port #0

[    0.598098] msm_serial 78af000.serial: uartclk = 1843199

[    0.598157] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 20, base_baud = 115199) is a MSM

[    0.598188] msm_serial: console setup on port #0

[    1.423054] console [ttyMSM0] enabled

[    1.428252] msm_serial: driver initialized

[    1.431678] msm_serial_hsl_init: driver initialized

[    1.725842] brd: module loaded

[    1.886522] loop: module loaded

[    1.906473] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64

[    1.908602] m25p80 spi32766.0: unrecognized JEDEC id bytes: 00,  0,  0

[    1.913569] phase not found in dts, falling to 50MHz

[    1.918958] QPIC platform data not populated

[    1.924095] QPIC controller hw version Major:2, Minor:1

[    1.928317] QPIC controller support serial nand.

[    1.933565] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x11

[    1.938132] nand: GigaDevice F50D1G41LB(2M) SPI NAND 1G 1.8V

[    1.944438] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64

[    1.950453] 20 ofpart partitions found on MTD device qcom_nand.0

[    1.957493] Creating 20 MTD partitions on "qcom_nand.0":

[    1.963625] 0x000000000000-0x000000080000 : "0:SBL1"

[    1.986554] 0x000000080000-0x000000100000 : "0:MIBIB"

[    1.988252] 0x000000100000-0x000000140000 : "0:BOOTCONFIG"

[    2.006520] 0x000000140000-0x000000180000 : "0:BOOTCONFIG1"

[    2.026447] 0x000000180000-0x000000280000 : "0:QSEE"

[    2.046504] 0x000000280000-0x000000380000 : "0:QSEE_1"

[    2.048534] 0x000000380000-0x0000003c0000 : "0:DEVCFG"

[    2.066473] 0x0000003c0000-0x000000400000 : "0:DEVCFG_1"

[    2.086503] 0x000000400000-0x000000440000 : "0:CDT"

[    2.106539] 0x000000440000-0x000000480000 : "0:CDT_1"

[    2.126540] 0x000000480000-0x000000500000 : "0:APPSBLENV"

[    2.146521] 0x000000500000-0x000000640000 : "0:APPSBL"

[    2.148801] 0x000000640000-0x000000780000 : "0:APPSBL_1"

[    2.166484] 0x000000780000-0x000000880000 : "0:ART"

[    2.186489] 0x000000880000-0x000000900000 : "0:TRAINING"

[    2.206484] 0x000000900000-0x000003640000 : "rootfs"

[    2.256495] mtd: device 15 (rootfs) set to be root filesystem

[    2.256779] mtdsplit: no squashfs found in "rootfs"

[    2.261235] 0x000003640000-0x000006380000 : "rootfs_1"

[    2.316520] 0x000006380000-0x000006c80000 : "pdt_data"

[    2.336548] 0x000006c80000-0x000007580000 : "pdt_data_1"

[    2.345079] 0x000007580000-0x000007680000 : "exp"

[    2.367224] libphy: Fixed MDIO Bus: probed

[    2.585901] qca-mdio 88000.mdio: Could not find phy-reset-gpio

[    2.586073] libphy: qca_mdio: probed

[    2.606345] qca-mdio 88000.mdio: qca-mdio driver was registered

[    3.045955] qca-mdio 90000.mdio: Could not find phy-reset-gpio

[    3.046127] libphy: qca_mdio: probed

[    3.052419] qca-mdio 90000.mdio: qca-mdio driver was registered

[    3.156176] Unable to create IPC log context!

[    3.156665] cnss[27]: INFO: Platform driver probed successfully. plat 9df60010 tgt 0x1104

[    3.160053] cnss[2]: INFO: Platform driver probed successfully. plat 9df70010 tgt 0xfffc

[    3.168162] i2c /dev entries driver

[    3.177171] qcom-tsens 4a8000.thermal-sensor: tsens calibration failed

[    3.206635] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com

[    3.207252] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 799999 KHz

[    3.214188] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1008000 KHz

[    3.221437] sdhci: Secure Digital Host Controller Interface driver

[    3.229876] sdhci: Copyright(c) Pierre Ossman

[    3.235943] sdhci-pltfm: SDHCI platform and OF driver helper

[    3.241743]

[    3.241743] Version Rollback Feature Disabled

[    3.248421] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss

[    3.251837] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available

[    3.260881] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000

[    3.267075] coresight-csr 6001000.csr: CSR initialized

[    3.274788] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000

[    3.279775] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000

[    3.287314] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000

[    3.294627] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000

[    3.302038] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000

[    3.309434] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000

[    3.316794] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000

[    3.324146] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000

[    3.331550] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000

[    3.338957] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000

[    3.346306] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000

[    3.353664] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000

[    3.361085] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000

[    3.368447] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000

[    3.375795] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000

[    3.383210] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000

[    3.390608] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000

[    3.398113] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000

[    3.405448] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000

[    3.412970] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x06064000

[    3.419904] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x06064000

[    3.435572] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x06064000

[    3.450084] sps:BAM 0x06064000 is registered.[    3.457251] coresight-tmc 6048000.tmc: TMC initialized

[    3.461353] coresight-tmc 6047000.tmc: TMC initialized

[    3.466570] coresight-funnel 6041000.funnel: FUNNEL initialized

[    3.471482] coresight-funnel 6100000.funnel: FUNNEL initialized

[    3.477339] coresight-funnel 6120000.funnel: FUNNEL initialized

[    3.483199] coresight-funnel 6130000.funnel: FUNNEL initialized

[    3.489153] coresight-funnel 61a1000.funnel: FUNNEL initialized

[    3.495741] coresight-etm4x 619c000.etm: ETM 4.0 initialized

[    3.501356] coresight-etm4x 619d000.etm: ETM 4.0 initialized

[    3.506943] coresight-replicator-qcom 6046000.replicator: REPLICATOR 1.0 initialized

[    3.512677] coresight-stm 6002000.stm: STM initialized

[    3.521532] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000

[    3.524872] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized

[    3.533218] Module switch init

[    3.544319] NET: Registered protocol family 10

[    3.556192] NET: Registered protocol family 17

[    3.556283] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.

[    3.559568] Bridge firewalling registered

[    3.572366] 8021q: 802.1Q VLAN Support v1.8

[    3.576569] Registering SWP/SWPB emulation handler

[    3.597422] ubi0: attaching mtd15

[    3.767752] random: nonblocking pool is initialized

[    3.772281] ubi0: scanning is finished

[    3.777315] ubi0: attached mtd15 (name "rootfs", size 45 MiB)

[    3.777338] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

[    3.782033] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

[    3.788841] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096

[    3.795658] ubi0: good PEBs: 362, bad PEBs: 0, corrupted PEBs: 0

[    3.802446] ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128

[    3.808693] ubi0: max/mean erase counter: 136/29, WL threshold: 4096, image sequence number: 1350110114

[    3.815714] ubi0: available PEBs: 0, total reserved PEBs: 362, PEBs reserved for bad PEB handling: 20

[    3.825054] ubi0: background thread "ubi_bgt0d" started, PID 114

[    3.886437] hctosys: unable to open rtc device (rtc0)

[    3.893490] ALSA device list:

[    3.893509]   No soundcards found.

[    3.898321] VFS: Mounted root (squashfs filesystem) readonly on device 31:23.

[    3.900191] Freeing unused kernel memory: 1024K (80c00000 - 80d00000)

[    4.298454] init: Console is alive

[    4.298661] init: - watchdog -

[    5.800373] Button Hotplug driver version 0.4.1

[    5.810339] SCSI subsystem initialized

[    5.825541] remoteproc remoteproc1: bt_rproc_driver is available

[    5.825627] bt_rproc_driver bt_rproc_driver: Probed

[    6.326063] init: - preinit -

Press the [f] key and hit [enter] to enter failsafe mode

Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level

Before mount_root

[    8.693865] UBIFS (ubi0:4): background thread "ubifs_bgt0_4" started, PID 149

[    8.712181] UBIFS (ubi0:4): recovery needed

[    8.782456] UBIFS (ubi0:4): recovery completed

[    8.782600] UBIFS (ubi0:4): UBIFS: mounted UBI device 0, volume 4, name "rootfs_data"

[    8.785806] UBIFS (ubi0:4): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

[    8.793747] UBIFS (ubi0:4): FS size: 7237632 bytes (6 MiB, 57 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)

[    8.803621] UBIFS (ubi0:4): reserved for root: 341850 bytes (333 KiB)

[    8.813510] UBIFS (ubi0:4): media format: w4/r0 (latest is w4/r0), UUID CA785B7F-613D-45DA-8867-3D1188E7F8A3, small LPT model

[    8.823799] mount_root: switching to jffs2 overlay

After mount_root

131072+0 records in

131072+0 records out

131072 bytes (128.0KB) copied, 0.578475 seconds, 221.3KB/s

131072+0 records in

131072+0 records out

131072 bytes (128.0KB) copied, 0.573077 seconds, 223.4KB/s

ln: /lib/firmware/IPQ5018/caldata.bin: File exists

ln: /lib/firmware/qcn9000/caldata_1.bin: File exists

[   10.071303] procd: - early -

[   10.071406] procd: - watchdog -

[   10.746161] procd: - ubus -

[   11.758395] procd: - init -

[   12.649923] ubi: mtd15 is already attached to ubi0BT FW mount is successful

 

[   12.821667] ubi: mtd15 is already attached to ubi0 WIFI FW mount is successful

[   14.790673] ntfs: driver 2.1.32 [Flags: R/O MODULE].

[   14.798372] Initializing XFRM netlink socket

[   14.799766] NET: Registered protocol family 15

[   14.987038] ssdk_switch_device_num_init[1159]:INFO:ess-switch dts node number: 2

[   14.987089] ssdk_dt_get_switch_node[970]:INFO:ess-switch DT exist!

[   14.993494] ssdk_dt_parse_access_mode[856]:INFO:switch_access_mode: local bus

[   14.999527] ssdk_dt_parse_access_mode[869]:INFO:switchreg_base_addr: 0x39c00000

[   15.006708] ssdk_dt_parse_access_mode[870]:INFO:switchreg_size: 0x200000

[   15.013805] ssdk_dt_parse_mac_mode[295]:INFO:mac mode = 0xf

[   15.020762] ssdk_dt_parse_mac_mode[301]:INFO:mac mode1 doesn't exit!

[   15.026057] ssdk_dt_parse_mac_mode[310]:INFO:mac mode2 doesn't exit!

[   15.032656] ssdk_dt_parse_port_bmp[757]:INFO:port_bmp doesn't exist!

[   15.039012] ssdk_dt_parse_uniphy[332]:INFO:ess-uniphy DT exist!

[   15.045320] ssdk_dt_parse_led[943]:INFO:current dts led_source_num is 1

[   15.051038] ssdk_plat_init start

[   17.465891] ssdk_mp_reset_init[739]:INFO:MP reset successfully!1

[   17.465953] ssdk_gcc_clock_init[1011]:INFO:SSDK gcc clock init successfully!

[   17.471655] mpge_phy_api_ops_init[1089]:INFO:qca probe mpge phy driver succeeded!

[   17.478411] regi_init[3557]:INFO:Initializing SCOMPHY!

[   18.609899] _adpt_mp_uniphy_clk_output_ctrl_set[236]:INFO:uniphy will output clock as 25000000Hz

[   18.610004] ssdk_led_init[152]:INFO:ssdk_led_mode:3, ssdk_led_map:ffc, ssdk_led_src_id:0

[   18.617877] ssdk_switch_register[1683]:INFO:Chip version 0xee

[   18.625832] qca_link_polling_select[1307]:INFO:link-polling-required node does not exist

[   18.631479] ssdk_switch_register[1717]:INFO:polling is selected

[   18.639626] regi_init[3567]:INFO:Initializing SCOMPHY Done!!

[   18.645277] ssdk_dt_get_switch_node[970]:INFO:ess-switch DT exist!

[   18.651182] ssdk_dt_parse_access_mode[856]:INFO:switch_access_mode: mdio

[   18.657162] ssdk_dt_parse_mac_mode[292]:INFO:mac mode doesn't exit!

[   18.664007] ssdk_dt_parse_mac_mode[301]:INFO:mac mode1 doesn't exit!

[   18.670009] ssdk_dt_parse_mac_mode[310]:INFO:mac mode2 doesn't exit!

[   18.676633] ssdk_dt_parse[1061]:INFO:switch node is qca83xx!

[   18.682929] ssdk_plat_init start

[   18.752972] f1_phy_api_ops_init[1517]:INFO:qca probe f1 phy driver succeeded!

[   18.752993] regi_init[3515]:INFO:Initializing ISISC!!

[   18.965875] qca_ar8327_gpio_reset[3448]:INFO:GPIO39 reset switch done

[   18.966052] ssdk_switch_register[1691]:INFO:Chip version 0x1302

[   18.971301] qca_link_polling_select[1307]:INFO:link-polling-required node does not exist

[   18.977035] ssdk_switch_register[1717]:INFO:polling is selected

[   20.625868] regi_init[3520]:INFO:Initializing ISISC Done!!

[   20.625986] regi_init[3590]:INFO:qca-ssdk module init succeeded!

[   20.639656] tun: Universal TUN/TAP device driver, 1.6

[   20.639684] tun: (C) 1999-2004 Max Krasnyansky <maxk@***.***>

[   20.651309] GMAC2(9d4fdd00) Invalid MAC@ - using f2:e0:0b:b1:7d:1b

[   20.652721] **********************************************************

[   20.656455] * NSS Data Plane driver

[   20.662892] **********************************************************

[   20.684679] l2tp_core: L2TP core driver, V2.0

[   20.685721] l2tp_netlink: L2TP netlink interface

[   20.947754] nss_driver - fw of size 712272  bytes copied to load addr: 40000000, nss_id : 0

[   20.949141] Supported Frequencies -

[   20.954900] 850 MHz 1 GHz

[   20.960536]

[   20.961472] 7f4a8540: set sdma 9ce22c00

[   20.963158] node size 2 # items 4

[   20.966502] memory: 40000000 536870912 (avl 440336384) items 4 active_cores 1

[   20.969928] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000

[   20.978321] 7f4a8540: NSS core 0 DDR from 40000000 to 41000000

[   20.983947] 7f4a8540: meminfo init succeed

[   21.030430] sit: IPv6 over IPv4 tunneling driver

[   21.036837] node size 2 # items 4

[   21.036866] memory: 40000000 536870912 (avl 440492032) items 4 active_cores 1

[   21.039131] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000

[   21.046301] 7f4a8540: nss core 0 booted successfully

[   21.058142] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.

[   21.073053] gre: GRE over IPv4 demultiplexor driver

[   21.075431] ip_gre: GRE over IPv4 tunneling driver

[   21.088356] ip6_gre: GRE over IPv6 tunneling driver

[   21.101495] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

[   21.129530] ip6_tables: (C) 2000-2006 Netfilter Core Team

[   21.140630] rmnet_nss_init(): initializing rmnet_nss

[   21.150981] nf_conntrack version 0.5.0 (6398 buckets, 25592 max)

[   21.165377] QCA Hy-Fi multicast installation successfully

[   21.173852] PPP generic driver version 2.4.2

[   21.179628] nss_lag_init[352]:LAG Manager Installed

[   21.183103] NET: Registered protocol family 24

[   21.188643] PPTP driver version 0.8.5

[   21.206731] diag: IPC Logging disabled

[   21.226788] TRACK: P[0]      PMask[4]

[   21.226810] TRACK: P[1]      PMask[4]

[   21.229145] TRACK: P[2]      PMask[4]

[   21.246452] TRACK: P[3]      PMask[4]

[   21.246525] nik 4097 info->svc_id

[   21.269535] QCA multicast snooping installed successfully

[   21.272429] <NSS-CRYPTO>:module loaded Build_ID - 05/18/21, 14:02:14 SoC=ipq50xx

[   21.310987] u32 classifier

[   21.311010]     input device check on

[   21.312602]     Actions configured

[   21.318568] Mirror/redirect action on

[   21.356704] fuse init (API version 7.23)

[   21.372946] arp_tables: (C) 2002 David S. Miller

[   21.381384] ip_tables: (C) 2000-2006 Netfilter Core Team

[   21.391213] l2tp_ppp: PPPoL2TP kernel driver, V2.0

[   21.467539] nf_conntrack_rtsp v0.6.21 loading

[   21.604298] nf_nat_rtsp v0.6.21 loading

[   21.615191] PPP MPPE Compression module registered

[   21.678009] xt_time: kernel timezone is -0000

qcawifi configuration is disable

[   26.615738] configuring additional NSS pbufs

[   26.629490] additional pbufs of size 3100672 got added to NSS

[   26.706335] mem_manager: module license 'Proprietary' taints kernel.

[   26.706363] Disabling lock debugging due to kernel taint

[   30.963508] vmap allocation for size 2908160 failed: use vmalloc=<size> to increase size.

[   31.140108] wlan: [1181:I:RPTR] qca_multi_link_init_module:

[   31.140108] ******QCA Repeater Initialization Done***********

[   31.140108]

***** starting cnssdaemon  -i integrated -i pci0 *****

*****cnssdaemon pid=1248*********

[   32.440150] cnss[27]: INFO: Setting daemon_support=1 for instance_id 0x27

[   32.530941] cnss[2]: INFO: Setting daemon_support=1 for instance_id 0x2

[   32.558895] cnss[27]: INFO: Setting cold_boot_support=1 for instance_id 0x27

[   32.648902] cnss[2]: INFO: Setting cold_boot_support=1 for instance_id 0x2

*********initiating cold boot calibration*************

[   34.318354] vmap allocation for size 937984 failed: use vmalloc=<size> to increase size.

[   34.338182] wlan: [1329:I:ANY] =======ol_if_register_wifi3_0==========

[   34.338182]

[   34.338228] wlan: [1329:I:ANY] osif_nss_register_module: NSS wifi ops registered for target_type:1 with soc_ops:a22a7c90

[   34.345029] wlan: [1329:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 2 bus_type 1

[   34.356168] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss

[   34.384798] remoteproc remoteproc0: Booting fw image IPQ5018/q6_fw.mdt, size 1052

[   35.295102] Subsystem error monitoring/handling services are up

[   35.296530] rpmsg_dev_probe: No pm domain

[   35.300381] rpmsg_dev_probe: No pm domain

[   35.300460] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up

[   35.300553] wlan: [1329:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 3 bus_type 1

[   35.300573] cnss[2]: INFO: Waiting for FW ready. Device: 0xfffc, FW ready timeout: 15 seconds

[   35.325277] cnss[2]: INFO: QMI WLFW service connected, state: 0x1

[   35.325594] diag: Receiving feature mask length more than Apps support

[   35.325686] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, 7f6a8bc4

[   35.346769] cnss[2]: INFO: device_id : 65532 mem mode : [1]

[   35.353505] cnss[2]: INFO: platform name: Qualcomm Technologies, Inc. IPQ5018/AP-MP03.1

[   35.372326] cnss[2]: INFO: Target capability: chip_id: 0x0, chip_family: 0x4, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x240e7fff, fw_build_timestamp: 2021-04-28 20:37, otp_version: 0x0 eeprom_caldata_read_timeout 0s

[   35.372381] cnss[2]: INFO: Using Boardid from bootargs:0x24

[   35.400394] cnss[2]: INFO: BDF location : 0x4ba00000

[   35.400422] cnss[2]: INFO: BDF IPQ5018/bdwlan.b24 size 131072

[   35.405298] cnss[2]: INFO: per device BDF location : 0x4ba20000

[   35.410411] cnss[2]: INFO: CALDATA IPQ5018/caldata.bin size 131072 offset 0x20000

[   35.525877] cnss[2]: INFO: FW ready received for device 0xfffc

[   35.527836] wlan: [1329:I:ANY] pld_ahb_wlan_enable: cnss_mode: Cold boot calibration

[   35.530603] cnss[2]: INFO: Sending mode message, mode: COLDBOOT CALIBRATION(7), state: 0xf

[   35.562987] wlan: [1329:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 2 bus_type 0

[   35.563126] cnss_pci 0001:01:00.0: BAR 0: assigned [mem 0xa0400000-0xa05fffff 64bit]

[   35.570173] cnss_pci 0001:01:00.0: enabling device (0140 -> 0142)

[   35.578995] cnss[27]: ERR: Unable to create CNSS MHI IPC log context

[   35.670415] cnss[2]: INFO: Coldboot Calibration completed successfully for device 0xfffc

[   36.582260] wlan: [1329:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 3 bus_type 0

[   36.582331] cnss[27]: INFO: Waiting for FW ready. Device: 0x1104, FW ready timeout: 15 seconds

[   36.596483] cnss[27]: INFO: QMI WLFW service connected, state: 0x11

[   36.601803] cnss[27]: INFO: device_id : 4356 mem mode : [1]

[   36.603944] cnss[27]: INFO: platform name: Qualcomm Technologies, Inc. IPQ5018/AP-MP03.1

[   36.734695] cnss[27]: INFO: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x240e7fff, fw_build_timestamp: 2021-04-28 20:22, otp_version: 0x0 eeprom_caldata_read_timeout 0s

[   36.747180] cnss[27]: INFO: Downloading BDF: qcn9000/bdwlan.ba0, size: 131072

[   36.772907] cnss[27]: INFO: Downloading BDF: qcn9000/caldata_1.bin, size: 131072

[   36.915925] cnss[27]: INFO: FW ready received for device 0x1104

[   36.915974] wlan: [1329:I:ANY] pld_pcie_wlan_enable: pld_pcie_wlan_enable: Invalid wlan_cfg config

[   36.920703] cnss[27]: INFO: Sending mode message, mode: COLDBOOT CALIBRATION(7), state: 0x1f

[   37.037358] wlan: [1329:I:ANY] init_ath_pci_3_0: 6ath_ol_pci_wifi3.0 :  (Atheros/multi-bss)

[   37.047720] wlan: [1342:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 0 bus_type 1

[   37.047766] cnss[2]: INFO: Sending mode message, mode: OFF(4), state: 0x7

[   37.056884] cnss[2]: INFO: QMI WLFW service disconnected, state: 0x6

[   37.076690] remoteproc remoteproc0: stopped remote processor cd00000.qcom_q6v5_wcss

[   37.076792] wlan: [1342:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 1 bus_type 1

[   37.106099] wlan: [1342:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 0 bus_type 0

[   37.106145] cnss[27]: INFO: Coldboot Calbration wait started for Device: 0x1104, timeout: 60 seconds

[   56.349924] cnss[27]: INFO: Coldboot Calibration completed successfully for device 0x1104

[   56.355966] cnss[27]: INFO: Coldboot Calibration wait ended for device 0x1104

[   56.357142] cnss[27]: INFO: Sending mode message, mode: OFF(4), state: 0x127

[   56.367497] cnss[27]: INFO: QMI WLFW service disconnected, state: 0x126

[   56.371390] cnss[27]: INFO: Shutting down QCN9000

[   56.378150] Removing device for chan:LOOPBACK

[   56.382620] mhi_reset_data_chan rp   (null) wp   (null)

[   56.386951] mhi_reset_data_chan rp   (null) wp   (null)

[   56.392136] Removing device for chan:DIAG

[   56.397464] mhi_reset_data_chan rp 9fe89000 wp 9fe89120

[   56.402095] mhi_reset_data_chan rp 9fe87000 wp 9fe87000

[   56.406940] Removing device for chan:IPCR

[   56.411556] mhi_reset_data_chan rp 9fe8d1b0 wp 9fe8d1a0

[   56.416043] mhi_reset_data_chan rp 9fe8b140 wp 9fe8b140

[   56.446038] wlan: [1342:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 1 bus_type 0

[   58.108563] vmap allocation for size 143360 failed: use vmalloc=<size> to increase size.

[   58.120224] wlan: [1355:I:ANY] =======ol_if_register_wifi3_0==========

[   58.120224]

[   58.120269] wlan: [1355:I:ANY] osif_nss_register_module: NSS wifi ops registered for target_type:1 with soc_ops:7fddfc90

[   58.127112] wlan: [1355:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 2 bus_type 1

[   58.138194] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss

[   58.146024] remoteproc remoteproc0: Booting fw image IPQ5018/q6_fw.mdt, size 1052

[   58.212920] Subsystem error monitoring/handling services are up

[   58.213642] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up

[   58.214316] rpmsg_dev_probe: No pm domain

[   58.214840] rpmsg_dev_probe: No pm domain

[   58.226944] cnss[2]: INFO: QMI WLFW service connected, state: 0x1

[   58.227338] diag: Receiving feature mask length more than Apps support

[   58.228292] cnss[2]: INFO: device_id : 65532 mem mode : [1]

[   58.240597] cnss[2]: INFO: platform name: Qualcomm Technologies, Inc. IPQ5018/AP-MP03.1

[   58.240598] cnss[2]: INFO: Target capability: chip_id: 0x0, chip_family: 0x4, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x240e7fff, fw_build_timestamp: 2021-04-28 20:37, otp_version: 0x0 eeprom_caldata_read_timeout 0s

[   58.240614] cnss[2]: INFO: Using Boardid from bootargs:0x24

[   58.241037] cnss[2]: INFO: BDF location : 0x4ba00000

[   58.241042] cnss[2]: INFO: BDF IPQ5018/bdwlan.b24 size 131072

[   58.241882] cnss[2]: INFO: per device BDF location : 0x4ba20000

[   58.242009] cnss[2]: INFO: CALDATA IPQ5018/caldata.bin size 131072 offset 0x20000

[   58.301662] wlan: [1355:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 3 bus_type 1

[   58.309273] cnss[2]: INFO: Waiting for FW ready. Device: 0xfffc, FW ready timeout: 15 seconds

[   58.317017] cnss[2]: INFO: FW ready received for device 0xfffc

[   58.326063] wlan: [1355:I:ANY] pld_ahb_wlan_enable: cnss_mode: Mission mode

[   58.331780] cnss[2]: INFO: Sending mode message, mode: MISSION(0), state: 0x7

[   58.343540] wlan: [1355:I:ANY] qca_napi_create: qca_napi_create: napi instance 0 created on pipe 4

[   58.346002] wlan: [1355:I:ANY] __ol_ath_attach: Allocated soc 9af00500

[   58.354669] wlan: [1355:D:dfs] WLAN_DEBUG_DFS1 : dfs_psoc_obj_create_notification: DFS obj attach to psoc successfully

[   58.383833] wlan: [1355:I:ANY] osif_nss_wifi_soc_setup: nss-wifili:#1 register wifili function for soc

[   58.383876] wlan: [1355:I:ANY] osif_nss_wifi_soc_setup: nss register id -1 nss config 3 Target Type 1d

[   58.392177] wlan: [1355:I:ANY] __ol_ath_attach: dev name soc0

[   58.402133] wlan: [1355:I:ANY] ol_ath_soc_attach: WMI attached. wmi_handle 9b107c00

[   58.412367] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   58.415147] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   58.425078] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   58.435167] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   58.445162] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   58.455270] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   58.465304] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   58.475388] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   58.486752] wlan: [1355:I:ANY] htc_wmi_init: HT Create . 9aed8000

[   58.495490] wlan: [1355:I:ANY] htc_wmi_init: Skipping BMI Done

[   58.502265] wlan: [1355:I:ANY] htc_wmi_init: host_enable 0 nss_nwifi_offload 0

[   58.519457] wlan: [1355:I:ANY] ol_target_init_complete: CDP soc attach success

[   58.519496] wlan: [1355:I:ANY] ol_target_init_complete: Soc attach success NSS config 0

[   58.525777] wlan: [1355:I:ANY] htc_set_async_ep: htc_set_async_ep: htc_handle 9aed8000, ep 2, value 1

[   58.534987] wlan: [886:I:TIF] HE_CAP Info = 9a08010d

[   58.543039] wlan: [886:I:TIF] Num HW modes = 1

[   58.548044] wlan: [886:I:TIF] Num PHY = 1

[   58.552263] wlan: [886:I:TIF] FW Build Version (Ext.) = 0

[   58.556361] wlan: [886:I:TIF] HDL Version: MajorVersion.MinorVersion = 0.0

[   58.561703] wlan: [886:I:TIF] Preferred HW Mode = 0 Num Radios = 1

[   58.568559] wlan: [886:W:TIF] add_11ax_mode_flags: 11AX wireless modes are not populated by the target in reg capabilities, adding 11AX wireless modes

[   58.574684] wlan: [886:I:TIF] init_deinit_add_11ax_modes: hw_mode_id = 0 phy_id = 0 wireless modes = 0

[   58.590882] wlan: [886:I:TIF] init_deinit_alloc_pdevs: CDP PDEV ATTACH success

[   58.597465] wlan: [886:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1

[   58.604808] wlan: [886:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0

[   58.611845] wlan: [886:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 9

[   58.619831] wlan: [886:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1

[   58.627234] wlan: [886:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0

[   58.634459] wlan: [886:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 9

[   58.642543] wlan: [886:I:TIF] init_deinit_get_total_beaconing_vdevs_for_soc: beacon_tx_offload_max_vdev: 9

[   58.649920] wlan: [886:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1

[   58.659587] wlan: [886:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0

[   58.666766] wlan: [886:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 9

[   58.674754] wlan: [886:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1

[   58.682141] wlan: [886:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0

[   58.690677] wlan: [886:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 9

[   58.697432] wlan: [886:I:ANY] init_deinit_update_pdev_tgt_info: pdev id:0 wmi_handle:9b107c00

[   58.705355] wlan: [886:F:DP] dp_rx_enable_mon_dest_frag: Feature DP_RX_MON_MEM_FRAG for mon_dest is enabled

[   58.717111] wlan: [886:I:ANY] init_deinit_update_pdev_tgt_info: Pdev = 0 Number of peers = 137 vdevs = 9

[   58.723033] wlan: [886:I:TIF] init_deinit_update_pdev_tgt_info: CDP PDEV INIT success

[   58.834138] wlan: [886:I:ANY] copy_fw_abi_version_tlv: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0

[   58.874621] wlan: [886:I:ANY] ready_extract_init_status_tlv: ready_extract_init_status_tlv:0

[   58.874664] wlan: [886:I:ANY] dp_peer_map_attach_wifi3: dp_peer_map_attach_wifi3 max_peers 163, max_ast_index: 528

[   58.874664]

[   58.882409] wlan: [1355:I:ANY] ol_ath_connect_htc: WMI is ready

[   58.910196] wlan: [1355:I:ANY] ath_get_radio_index: Error: Could not match the device name : wifi%d

[   58.910239] wlan: [1355:E:NSS] [nss-wifili]: pdev:971c0500 radio_ifnum:28 scheme_id:1 radio_priority:0

[   58.923994] wlan: [1355:E:TIF] target_if_lro_hash_config: pdev with id 0 is NULL

[   58.930530] wlan: [1355:I:ANY] ol_ath_soc_attach: connect HTC

[   58.935280] wlan: [1355:I:ANY] ol_ath_soc_attach: bypasswmi : 0

[   58.941235] wlan: [1355:I:MSCS] qca_mscs_module_init:

[   58.941235] ****QCA MSCS Initialization Done**** SoC 9af00500

[   58.946718] wlan: [1355:I:ANY] ol_ath_soc_attach: UMAC attach

[   58.958748] wlan: [1355:I:ANY] __ol_ath_attach: pdev_netdev name wifi0

[   58.963663] wlan: [1355:I:ANY] __ol_ath_attach: Skip txrx_pdev_attach_target

[   58.969867] wlan: [1355:I:ANY] __ol_ath_attach: BURSTING enabled by default

[   58.977679] wlan: [1355:I:ANY] ol_ath_pdev_attach: interface_id 0

[   58.983537] wlan: [1355:I:TIF] ol_ath_pdev_regdmn_init:  phy id = 0 Modes supported

[   58.991152] wlan: [1355:I:TIF] ol_ath_pdev_regdmn_init:  11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1

[   58.997545] wlan: [1355:I:TIF] ol_ath_pdev_regdmn_init:  Reg cap - phy_id = 0 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0

[   59.007039] wlan: [1355:I:ANY] ol_ath_update_wireless_modes: wireless_modes = 680680c before update

[   59.021195] wlan: [1355:I:ANY] ol_ath_update_wireless_modes: Wireless_modes = 680680c after update

[   59.029935] wlan: [1355:I:ANY] ol_ath_update_ext_caps: 11ax 2G supported case

[   59.039204] wlan: [1355:I:MBSSIE] ol_ath_assign_mbssid_ref_bssid: MBSSID reference bssid is 02:03:7f:12:4c:12 soc: soc0 pdev: wifi0

[   59.046454] wlan: [1355:I:MBSSIE] ieee80211_mbss_attach: :>

[   59.057878] wlan: [1355:I:MBSSIE] ieee80211_mbss_attach: :<

[   59.063332] wlan: [1355:I:ANY] ol_resmgr_create: OL Resmgr Init-ed

[   59.069215] wlan: [1355:I:ANY] acfg_attach: acfg_attach: 3288: Netlink socket created:9a046000

[   59.075168] wlan: [1355:I:ANY] ol_ath_stats_attach: periodic_chan_stats: 1

[   59.084251] wlan: [1355:I:ANY] wlan_scan_update_channel_list: num_chan: 11

[   59.092013] wlan: [0:I:ANY] ol_ath_pdev_attach: Set global_ic[1], ptr:a2efc0e8

[   59.097424] wlan: [0:I:ANY] dp_lag_soc_enable: pdev(9d475804) Enabling DBDC Repeater 0

[   59.104715] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed

[   59.112975] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: pdev(9d475804) is_primary 0

[   59.120924] wlan: [1355:I:ANY] ol_ath_twt_enable_command: TWT is disable in INI. Do not send enable cmd to FW

[   59.133095] wlan: [1355:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: cfg block channel list is empty

[   59.138745] wlan: [1355:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: pdev_idx = 0 tx_desc_limit = 8192

[   59.148005] wlan: [1355:I:ANY] osif_wrap_attach: osif wrap attached

[   59.148005]

[   59.157031] wlan: [1355:I:ANY] osif_wrap_devt_init: osif wrap dev table init done

[   59.157031]

[   59.164908] wlan: [1355:I:ANY] osif_wrap_attach:  Wrap Attached: Wrap_com =95cca000 ic->ic_wrap_com=95cca000 &wrap_com->wc_devt=95cca000

[   59.164908]

[   59.173753] wlan: [1355:I:ANY] __ol_ath_attach: needed_headroom reservation 60

[   59.188784] wlan: [1355:I:ANY] ol_ath_enable_fraglist: Enabled Fraglist bit for the radio wifi0 features 41

[   59.194667] wlan: [1355:I:ANY] wlan_cfg80211_init: Number of 2G channels: 11

[   59.205181] wlan: [1355:I:ANY] ieee80211_cfg80211_radio_attach: ic: 0x971c0500, wdev: 0x971d7d38, wiphy: 0x96049160, netdev: 0x971c0000

[   59.214652] wlan: [1355:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: Running with HW mode = 0

[   59.225685] wlan: [1355:E:QLD] qld_register: Handle or address is NULL

[   59.234793] wlan: [1355:I:ANY] wlan_pdev_operation: num_radios=1, wifi_radios[0].sc = 971c0500_radio_type = 2

[   59.241382] wlan: [1355:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 2 bus_type 0

[   59.250205] cnss_pci 0001:01:00.0: BAR 0: assigned [mem 0xa0400000-0xa05fffff 64bit]

[   59.258474] cnss[27]: ERR: Unable to create CNSS MHI IPC log context

[   59.506792] wlan: [1355:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 3 bus_type 0

[   59.506869] cnss[27]: INFO: Waiting for FW ready. Device: 0x1104, FW ready timeout: 15 seconds

[   59.518079] cnss[27]: INFO: QMI WLFW service connected, state: 0x11

[   59.527762] cnss[27]: INFO: device_id : 4356 mem mode : [1]

[   59.528738] cnss[27]: INFO: platform name: Qualcomm Technologies, Inc. IPQ5018/AP-MP03.1

[   59.538387] cnss[27]: INFO: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x240e7fff, fw_build_timestamp: 2021-04-28 20:22, otp_version: 0x0 eeprom_caldata_read_timeout 0s

[   59.542671] cnss[27]: INFO: Downloading BDF: qcn9000/bdwlan.ba0, size: 131072

[   59.582123] cnss[27]: INFO: Downloading BDF: qcn9000/caldata_1.bin, size: 131072

[   59.615963] cnss[27]: INFO: FW ready received for device 0x1104

[   59.617082] cnss[27]: INFO: Sending mode message, mode: MISSION(0), state: 0x17

[   59.647126] wlan: [1355:I:ANY] qca_napi_create: qca_napi_create: napi instance 0 created on pipe 4

[   59.647411] wlan: [1355:I:ANY] __ol_ath_attach: Allocated soc 95d80500

[   59.655064] wlan: [1355:D:dfs] WLAN_DEBUG_DFS1 : dfs_psoc_obj_create_notification: DFS obj attach to psoc successfully

[   59.662422] wlan: [1355:E:QDF] CONFIG creation failed

[   59.672337] wlan: [1355:I:ANY] osif_nss_wifi_soc_setup: nss-wifili:#1 register wifili function for soc

[   59.677319] wlan: [1355:I:ANY] osif_nss_wifi_soc_setup: nss register id -1 nss config 3 Target Type 1a

[   59.686547] wlan: [1355:I:ANY] __ol_ath_attach: dev name soc1

[   59.696396] wlan: [1355:I:ANY] ol_ath_soc_attach: WMI attached. wmi_handle 95034000

[   59.707339] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   59.709589] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   59.719417] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   59.729476] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   59.739548] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   59.749612] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   59.759678] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   59.769746] wlan: [1355:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 3

[   59.779898] wlan: [1355:I:ANY] htc_wmi_init: HT Create . 9d716000

[   59.789894] wlan: [1355:I:ANY] htc_wmi_init: Skipping BMI Done

[   59.796135] wlan: [1355:I:ANY] htc_wmi_init: host_enable 0 nss_nwifi_offload 0

[   59.805172] wlan: [1355:F:ANY] dp_config_full_mon_mode: Configure full monitor mode val: 1

[   59.817711] wlan: [1355:I:ANY] ol_target_init_complete: CDP soc attach success

[   59.817747] wlan: [1355:I:ANY] ol_target_init_complete: Soc attach success NSS config 0

[   59.824758] wlan: [1355:I:ANY] htc_set_async_ep: htc_set_async_ep: htc_handle 9d716000, ep 2, value 1

[   59.834713] wlan: [1332:I:TIF] HE_CAP Info = 9a08010d

[   59.841986] wlan: [1332:I:TIF] Num HW modes = 1

[   59.847123] wlan: [1332:I:TIF] Num PHY = 1

[   59.851332] wlan: [1332:I:TIF] FW Build Version (Ext.) = 199

[   59.855493] wlan: [1332:I:TIF] HDL Version: MajorVersion.MinorVersion = 7.3

[   59.861344] wlan: [1332:I:TIF] Preferred HW Mode = 0 Num Radios = 1

[   59.868086] wlan: [1332:W:TIF] add_11ax_mode_flags: 11AX wireless modes are not populated by the target in reg capabilities, adding 11AX wireless modes

[   59.874254] wlan: [1332:I:TIF] init_deinit_add_11ax_modes: hw_mode_id = 0 phy_id = 0 wireless modes = 0

[   59.889411] wlan: [1332:I:TIF] init_deinit_alloc_pdevs: CDP PDEV ATTACH success

[   59.897250] wlan: [1332:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1

[   59.904459] wlan: [1332:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0

[   59.912126] wlan: [1332:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 9

[   59.919881] wlan: [1332:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1

[   59.927650] wlan: [1332:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0

[   59.935014] wlan: [1332:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 9

[   59.942766] wlan: [1332:I:TIF] init_deinit_get_total_beaconing_vdevs_for_soc: beacon_tx_offload_max_vdev: 9

[   59.950567] wlan: [1332:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1

[   59.960024] wlan: [1332:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0

[   59.967665] wlan: [1332:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 9

[   59.975376] wlan: [1332:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1

[   59.983324] wlan: [1332:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0

[   59.990594] wlan: [1332:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 9

[   59.998324] wlan: [1332:I:ANY] init_deinit_update_pdev_tgt_info: pdev id:0 wmi_handle:95034000

[   60.006793] wlan: [1332:F:DP] dp_rx_enable_mon_dest_frag: Feature DP_RX_MON_MEM_FRAG for mon_dest is enabled

[   60.018400] wlan: [1332:I:ANY] init_deinit_update_pdev_tgt_info: Pdev = 0 Number of peers = 137 vdevs = 9

[   60.024515] wlan: [1332:I:TIF] init_deinit_update_pdev_tgt_info: CDP PDEV INIT success

[   60.134259] wlan: [1332:I:ANY] copy_fw_abi_version_tlv: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0

[   60.454250] wlan: [1332:I:ANY] ready_extract_init_status_tlv: ready_extract_init_status_tlv:0

[   60.454294] wlan: [1332:I:ANY] dp_peer_map_attach_wifi3: dp_peer_map_attach_wifi3 max_peers 163, max_ast_index: 528

[   60.454294]

[   60.461905] wlan: [1355:I:ANY] ol_ath_connect_htc: WMI is ready

[   60.489654] wlan: [1355:I:ANY] ath_get_radio_index: Error: Could not match the device name : wifi%d

[   60.489705] wlan: [1355:E:NSS] [nss-wifili]: pdev:94c80500 radio_ifnum:29 scheme_id:0 radio_priority:1

[   60.503207] wlan: [1355:E:TIF] target_if_lro_hash_config: pdev with id 0 is NULL

[   60.507675] wlan: [1355:I:ANY] ol_ath_soc_attach: connect HTC

[   60.514537] wlan: [1355:I:ANY] ol_ath_soc_attach: bypasswmi : 0

[   60.520257] wlan: [1355:I:MSCS] qca_mscs_module_init:

[   60.520257] ****QCA MSCS Initialization Done**** SoC 95d80500

[   60.525929] wlan: [1355:I:ANY] ol_ath_soc_attach: UMAC attach

[   60.537195] wlan: [1355:I:ANY] __ol_ath_attach: pdev_netdev name wifi1

[   60.542672] wlan: [1355:I:ANY] __ol_ath_attach: Skip txrx_pdev_attach_target

[   60.549114] wlan: [1355:I:ANY] __ol_ath_attach: BURSTING enabled by default

[   60.556432] wlan: [1355:I:ANY] ol_ath_pdev_attach: interface_id 1

[   60.562973] wlan: [1355:I:TIF] ol_ath_pdev_regdmn_init:  phy id = 0 Modes supported

[   60.569247] wlan: [1355:I:TIF] ol_ath_pdev_regdmn_init:  11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1

[   60.576716] wlan: [1355:I:TIF] ol_ath_pdev_regdmn_init:  Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4900, hi_5g = 5920

[   60.586421] wlan: [1355:I:ANY] ol_ath_update_wireless_modes: wireless_modes = f97f9001 before update

[   60.600563] wlan: [1355:I:ANY] ol_ath_update_wireless_modes: Wireless_modes = f97f9001 after update

[   60.609789] wlan: [1355:I:ANY] ol_ath_update_ext_caps: 11ax 5G supported case

[   60.618671] wlan: [1355:I:MBSSIE] ol_ath_assign_mbssid_ref_bssid: MBSSID reference bssid is 02:03:7f:12:cc:6c soc: soc1 pdev: wifi1

[   60.626053] wlan: [1355:I:MBSSIE] ieee80211_mbss_attach: :>

[   60.637462] wlan: [1355:I:MBSSIE] ieee80211_mbss_attach: :<

[   60.643009] wlan: [1355:I:ANY] ol_resmgr_create: OL Resmgr Init-ed

[   60.648834] wlan: [1355:I:ANY] acfg_attach: acfg_attach: Offload using existing sock 9a046000

[   60.654802] wlan: [1355:I:ANY] acfg_attach: Offload using existing sock 9a046000

[   60.654802]

[   60.663433] wlan: [1355:I:ANY] ol_ath_stats_attach: periodic_chan_stats: 1

[   60.673903] wlan: [1355:I:ANY] wlan_scan_update_channel_list: num_chan: 25

[   60.679190] wlan: [0:I:ANY] ol_ath_pdev_attach: Set global_ic[2], ptr:a2efc0e8

[   60.685913] wlan: [0:I:ANY] dp_lag_soc_enable: pdev(9b7c2a04) Enabling DBDC Repeater 0

[   60.693212] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: pdev(9b7c2a04) is_primary 0

[   60.693251] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed

[   60.708991] wlan: [1355:I:ANY] ol_ath_twt_enable_command: TWT is disable in INI. Do not send enable cmd to FW

[   60.723669] wlan: [1355:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: cfg block channel list is empty

[   60.727160] wlan: [1355:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: pdev_idx = 0 tx_desc_limit = 8192

[   60.736385] wlan: [1355:I:ANY] osif_wrap_attach: osif wrap attached

[   60.736385]

[   60.745429] wlan: [1355:I:ANY] osif_wrap_devt_init: osif wrap dev table init done

[   60.745429]

[   60.753360] wlan: [1355:I:ANY] osif_wrap_attach:  Wrap Attached: Wrap_com =9d569800 ic->ic_wrap_com=9d569800 &wrap_com->wc_devt=9d569800

[   60.753360]

[   60.762156] wlan: [1355:I:ANY] __ol_ath_attach: needed_headroom reservation 60

[   60.775920] wlan: [1355:I:ANY] ol_ath_enable_fraglist: Enabled Fraglist bit for the radio wifi1 features 41

[   60.783531] wlan: [1355:I:ANY] ieee80211_cfg80211_radio_attach: ic: 0x94c80500, wdev: 0x94c97d38, wiphy: 0x942a9960, netdev: 0x94c80000

[   60.794497] wlan: [1355:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: Running with HW mode = 0

[   60.806380] wlan: [1355:E:QLD] qld_register: Handle or address is NULL

[   60.815026] wlan: [1355:I:ANY] wlan_pdev_operation: num_radios=2, wifi_radios[1].sc = 94c80500_radio_type = 2

[   60.822315] Event 0x3 is registered for RC 0

[   60.831490] wlan: [1355:I:ANY] init_ath_pci_3_0: 6ath_ol_pci_wifi3.0 :  (Atheros/multi-bss)

[   60.947050] vmap allocation for size 577536 failed: use vmalloc=<size> to increase size.

[   60.947698] vmap allocation for size 102400 failed: use vmalloc=<size> to increase size.

[   60.987501] wlan: [1402:I:ANY] osif_nss_register_module: NSS wifi ops registered for target_type:0 with soc_ops:a1caa070

[   60.988148] wlan: [1402:I:ANY] init_ath_pci_2_0: 6ath_ol_pci_2_0:  (Atheros/multi-bss)

No Direct-Attach chipsets found.

acfg_tool: Issuing blocking call to wait for events

acfg_tool: Issuing blocking call to wait for events

[   68.777065] vmap allocation for size 1155072 failed: use vmalloc=<size> to increase size.

[   68.853470] ECM init

[   68.853561] ECM database jhash random seed: 0x74334582

[   68.895948] ECM init complete

[   69.438591] device eth1 entered promiscuous mode

[   69.440643] br-lan: port 1(eth1) entered forwarding state

[   69.442325] br-lan: port 1(eth1) entered forwarding state

[   69.476565] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[   71.435945] br-lan: port 1(eth1) entered forwarding state

[   72.561651] mc_attach: enabled snooping on br-lan.

[   73.103532] sh (2968): drop_caches: 3

**** Platform Name: ap-mp03.1 *****

Copy ART caldata from /dev/mtdblock13 to /tmp/virtual_art.bin

[   74.895221] ubi1: attaching mtd17

[   74.932802] ubi1: scanning is finished

[   74.938352] ubi1: attached mtd17 (name "pdt_data", size 9 MiB)

[   74.938379] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

[   74.943627] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

[   74.950131] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096

[   74.956902] ubi1: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0

[   74.963621] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128

[   74.969541] ubi1: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 1348815590

[   74.976875] ubi1: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for bad PEB handling: 20

[   74.987426] ubi1: background thread "ubi_bgt1d" started, PID 3111

[   75.018352] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 3115

[   75.037266] UBIFS (ubi1:0): recovery needed

[   75.112581] UBIFS (ubi1:0): recovery completed

[   75.112716] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "pdt_data"

[   75.116048] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

[   75.123578] UBIFS (ubi1:0): FS size: 4825088 bytes (4 MiB, 38 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)

[   75.133837] UBIFS (ubi1:0): reserved for root: 227900 bytes (222 KiB)

[   75.143498] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 1E582E77-0A05-4836-AE3D-3C3813ED0E91, small LPT model

[do_setup.833]: start init: MW_CFG_Init

 

[do_setup.833]: start init: IF_EventInit

 

[do_setup.833]: start init: Mp_if_init

 

[do_setup.833]: start init: MP_CFG_Start

 

[check_mount_ready.925]: /dev/ubi1_0 /mnt ubifs rw,relatime 0 0

 

 

[check_mount_ready.928]:

Format: Log Type - Time(microsec) - Message - Optional Info

Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic

S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1.1-00044

S - IMAGE_VARIANT_STRING=MAACANAZA

S - OEM_IMAGE_VERSION_STRING=node-sh-06

S - Boot Config, 0x000002c5

B -       128 - PBL, Start

B -      1564 - bootable_media_detect_entry, Start

B -      3356 - bootable_media_detect_success, Start

B -      3360 - elf_loader_entry, Start

B -      8443 - auth_hash_seg_entry, Start

B -      8802 - auth_hash_seg_exit, Start

B -     99260 - elf_segs_hash_verify_entry, Start

B -    167264 - PBL, End

B -    137860 - SBL1, Start

B -    198311 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4

B -    206637 - clock_init, Start

D -      7289 - clock_init, Delta

B -    214079 - boot_flash_init, Start

D -     17964 - boot_flash_init, Delta

B -    232105 - boot_config_data_table_init, Start

D -      5002 - boot_config_data_table_init, Delta - (575 Bytes)

B -    240187 - Boot Setting :  0x00000618

B -    246379 - CDT version:2,Platform ID:8,Major ID:4,Minor ID:0,Subtype:1

B -    253302 - sbl1_ddr_set_params, Start

B -    254888 - Pre_DDR_clock_init, Start

B -    260561 - Pre_DDR_clock_init, End

B -    803949 - do ddr sanity test, Start

D -        30 - do ddr sanity test, Delta

B -    808616 - Image Load, Start

D -    234819 - QSEE Image Loaded, Delta - (523680 Bytes)

B -   1044259 - Image Load, Start

D -     14640 - DEVCFG Image Loaded, Delta - (13592 Bytes)

B -   1058929 - Image Load, Start

D -    186569 - APPSBL Image Loaded, Delta - (419920 Bytes)

B -   1245589 - QSEE Execution, Start

D -        30 - QSEE Execution, Delta

B -   1252055 - SBL1, End

D -   1116666 - SBL1, Delta

S - Flash Throughput, 2289 KB/s  (958439 Bytes,  418573 us)

S - DDR Frequency, 800 MHz

S - Core 0 Frequency, 800 MHz

 

 

U-Boot 2016.01 (May 18 2021 - 13:19:54 +0800)

 

DRAM:  smem ram ptable found: ver: 1 len: 4

512 MiB

NAND:  QPIC controller support serial NAND

ID = 7f7f11c8

Vendor = c8

Device = 11

Serial Nand Device Found With ID : 0xc8 0x11

Serial NAND device Manufature:F50D1G41LB(2M)

Device Size:128 MiB, Page size:2048, Spare Size:64, ECC:4-bit

SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000

ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)

128 MiB

MMC:   sdhci: Node Not found, skipping initialization

 

PCI Link Intialized

PCI1 is not defined in the device tree

In:    serial@78AF000

Out:   serial@78AF000

Err:   serial@78AF000

machid: 8040001

eth0 MAC Address from ART is not valid

eth1 MAC Address from ART is not valid

 

***************************************************************************

*                                                                         *

*                       H3C BX54E Boot, Version 102                       *

*                                                                         *

***************************************************************************

 

Hit any key to stop autoboot:  0

ubi0: attaching mtd1

ubi0: scanning is finished

ubi0: attached mtd1 (name "mtd=0", size 45 MiB)

ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096

ubi0: good PEBs: 362, bad PEBs: 0, corrupted PEBs: 0

ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128

ubi0: max/mean erase counter: 136/29, WL threshold: 4096, image sequence number: 1350110114

ubi0: available PEBs: 0, total reserved PEBs: 362, PEBs reserved for bad PEB handling: 20

Read 0 bytes from volume kernel to 44000000

No size specified -> Using max size (4077388)

## Loading kernel from FIT Image at 44000000 ...

   Using 'config@mp03.1' configuration

   Trying 'kernel@1' kernel subimage

     Description:  ARM OpenWrt Linux-4.4.60

     Type:         Kernel Image

     Compression:  lzma compressed

     Data Start:   0x440000e4

     Data Size:    2950128 Bytes = 2.8 MiB

     Architecture: ARM

     OS:           Linux

     Load Address: 0x41208000

     Entry Point:  0x41208000

     Hash algo